Big Red Laser: Difference between revisions

Tools
Model	Universal Laser System ILS 12.5
Room	Laser Room
Work envelope/max capacity	48" x 24" x 12"; max part 52.5 x 30 x 12 in;
Link to manual	https://cdn.ulsinc.com/assets/pdf/user_guides/5c786e453cc4b2555c25b914/ils_user_guide.pdf
Related tools	;
Trainer(s)	John Hache
Training Sessions	Big Red Laser Training;
Knowledge keeper(s)
Training document(s)
Material Safety Data Sheet (MSDS)
Safe Work Procedure	https://northforge.ca/community/wp-content/uploads/2023/09/ILS-Universal-SWP.pdf#new_tab
Consumables
Software	CorelDraw;
Equipment type	tool

← Older edit

VisualWikitext

Latest revision as of 16:33, 2024 October 24

Laser Room Precautions apply

You will be working in the Laser Room . In order to keep safe from hazards created by you or other workers using any of the tools in this room, the following precautions apply in addition to any other precautions:

Safety

Hazards: fumes, fire, noise, lacerations.
Wear hearing protection when the exhaust fan is on, as it's loud enough to cause hearing damage.
Check the debris tray before and after. Debris buildup can cause a fire as the laser cuts through the workpiece and enters the debris tray.
Do not cut unknown or unapproved materials. If the material is not on the approved list, ask for permission on Slack.
Heat can build up when doing multiple passes on wood, causing the material to ignite. If you're cutting thick wood and it doesn't go through in three passes, stop.
Do not cut multiple layers of fabric, paper, cardboard, etc at one time. The increased air between the layers can increase the risk of fire.
Note when cutting lightweight materials like fabric or paper: any cutouts produced can be blown around by the air support and exhaust; if they pass between the lens and the material they can cause a fire or blow out the lens.
Always use a vector grid when cutting all the way through.
Don't wear loose hair, clothing, jewellery, etc. as they can become entangled in the belts.

Running lasers unattended

Due to risk of fire, do not leave the lasers running unattended. You must be close to the lasers and able to respond quickly in case of emergency. In particular, pay close attention to the laser when it is running in vector mode as the fire risk is greatly increased compared to vector mode.

Interlocked enclosures and laser classification

Never circumvent the interlocked enclosures on our laser cutters
Our laser cutters all contain lasers that would be considered Class 4 and subject to significant training and restrictions.
The laser cutters implement an interlocked safety enclosure that shuts off the laser if the enclosure is opened. This reclassifies the machines to a Class 1 laser for the purpose of the actual cutting laser that is interlocked.
However, the laser cutters end up being Class 2 laser because of the red dot pointer laser that can operate even with the lid open.

Housekeeping

When using Big Blue, Little Blue, and Big Red: Clean the lens before the start of your session. Monitor the lens throughout - cutting messy materials like rubber may require recleaning. Note that Big Red has one extra mirror that needs to be cleaned in addition to the one in the head.
When using Giant Blue, check the lens frequently for debris buildup and clean as required.
Always use a lens tissue when cleaning the lens - bare Q-tips are mildly abrasive and wear away at the coatings on the lens
Break down waste before bagging (pieces should be smaller than 6" x 6"). Blunt any sharp edges so they don't break the bag.

for all	that is a bigger garbage issue... see Todo

The Blue Laser Room vacuum is located by Big Red for your use.

for all	Safety1 Manual says "NEVER OPERATE THE LASER SYSTEM WITHOUT CONSTANT SUPERVISION OF THE CUTTING AND ENGRAVING PROCESS. "

Instructions:Big Red Laser doesn't exist yet

@@ Line 1: / Line 1: @@
 {{Tool
+|photo=Laser_Room_-_Universal_ILS_12.5_AKA_Big_Red.png
 |room=Laser Room
 |model=Universal Laser System ILS 12.5
 |work envelope=* 48" x 24" x 12"
+* max part 52.5 x 30 x 12 in
 |link to manual=https://cdn.ulsinc.com/assets/pdf/user_guides/5c786e453cc4b2555c25b914/ils_user_guide.pdf
 |trainers=John Hache
@@ Line 8: / Line 10: @@
 |other details=* [https://www.ulsinc.com/products/platforms/ils12150d Big Red (Universal Laser Systems ILS12.150D 24" x 48")]
 * [http://service.ulsinc.com/support/Service%20Manuals%20&%20Maintenance%20Procedures/Platform_VLSDT_VLS_PLS_ILS/Platform_ILS/Individual%20Procedures/Adjustments%20and%20Settings/ technical documents]
+{{Discuss | Safety1
+* Manual says "NEVER OPERATE THE LASER SYSTEM WITHOUT CONSTANT SUPERVISION OF THE
+CUTTING AND ENGRAVING PROCESS. "
+}}
 }}