Eye Wash Station: Difference between revisions

Latest revision as of 21:42, 2024 August 13

Whatever is discussed in here likely also applies to Fire Extinguisher.

for all	Doug pointed out that we may not have good documentation on these, let's change that. Here is a start... This should contain instructions on how to use the eye wash stations. It should probably also include whom to notify, and a link to the incident form, since use of a wash station would warrant a form. Maybe the form is how we find out that they were used, too. As much as that is internal info, I think it might also be good to add if we have spares on hand, and possibly where we get them.

for all	We'll either need to find a way to link this to most rooms, or better yet, make it eye hazard dependent and link it that way... TT needs to think about this some more. There is a maps functionality for the wiki, and it can use any base map we want with coordinates. So we would be able to display e.g. tools or safety equipment via coordinate. I had thought about adding this initially but decided not to follow that squirrel for now. Let me know if I should reconsider that. Ttenbergen (talk) 22:42, 2024 August 13 (CDT) Rooms and locations listed for convenience, there's probably a better way to do this in terms of the Wiki. John has also taken photos of the locations in case that's helpful later. That would be helpful later, because for the map we would probably encode each as its own "tool" (even if that stretches that category a bit), so a photo on there would be helpful. Ttenbergen (talk) 22:42, 2024 August 13 (CDT)

North Forge supplies eye wash stations for use in case of eye irritation. If you use the eye wash station, please fill out an Incident Report Form.

Use

Remove the lid
If only one eye is affected, tilt your head so that the affected eye is lower. This prevents contaminants from being washed into the unaffected eye.
Hold the bottle against your face over the eye and squeeze.
While squeezing, move your eyeball around to access as much of the surface as possible.
If necessary, also raise your eyelids using a finger to dislodge any contaminants under the eyeball.

Locations

1st Floor

Design Space

Beside the door leading to the metalworking area/back lane (to the left when facing the door)

Metalworking Room

On the wall beside the main entrance door by the air tank (to the left when facing the door)
On the wall to the right of the metal lathe

3rd Floor

General Assembly Area:

On the wall between the IoT Innovation Lab and the 3D printing room
On the wall outside the tool room (to the right of the door)
Inside Tiny Maker Mind workshop, on the wall opposite the door (member-owned space, do not enter except in case of emergency)
To the right of the back elevator/directly across from the paint booth
On the wall directly beside the main entrance (to the left when facing the door)

CNC Woodworking Room

On the wall directly beside the door (to the right when fcing the door)

Woodworking Room

On the wall directly beside the door (to the right when facing the door)

Epoxy Room

On the wall directly beside the door (to the right when facing the door

Laser Room

On the wall directly beside the door (to the right when facing the door)

3D Printing Room

Inside the room on the wall directly beside the door (to the right when facing the door).

IoT Innovation Lab

Inside the room on the wall beside the door (to the left when facing the door).

@@ Line 1: / Line 1: @@
-Whatever is discussed in here likely also applies to [[Fire extinguisher]].
+Whatever is discussed in here likely also applies to [[Fire Extinguisher]].
 {{Discuss| Doug pointed out that we may not have good documentation on these, let's change that. Here is a start...
@@ Line 8: / Line 8: @@
 }}
-{{Discuss| We'll either need to find a way to link this to most rooms, or better yet, make it eye hazard dependent and link it that way... TT needs to think about this some more. }}
+{{Discuss|
+* We'll either need to find a way to link this to most rooms, or better yet, make it eye hazard dependent and link it that way... TT needs to think about this some more.
+** There is a maps functionality for the wiki, and it can use any base map we want with coordinates. So we would be able to display e.g. tools or safety equipment via coordinate. I had thought about adding this initially but decided not to follow that squirrel for now. Let me know if I should reconsider that. [[User:Ttenbergen|Ttenbergen]] ([[User talk:Ttenbergen|talk]]) 22:42, 2024 August 13 (CDT)
+* Rooms and locations listed for convenience, there's probably a better way to do this in terms of the Wiki. John has also taken photos of the locations in case that's helpful later.
+** That would be helpful later, because for the map we would probably encode each as its own "tool" (even if that stretches that category a bit), so a photo on there would be helpful. [[User:Ttenbergen|Ttenbergen]] ([[User talk:Ttenbergen|talk]]) 22:42, 2024 August 13 (CDT)
+}}
+[[Category:Safety]]
+North Forge supplies eye wash stations for use in case of eye irritation. If you use the eye wash station, please fill out an [https://northforge.ca/safety/ Incident Report Form].
+==Use==
+#Remove the lid
+#If only one eye is affected, tilt your head so that the affected eye is lower. This prevents contaminants from being washed into the unaffected eye.
+#Hold the bottle against your face over the eye and squeeze.
+#While squeezing, move your eyeball around to access as much of the surface as possible.
+#If necessary, also raise your eyelids using a finger to dislodge any contaminants under the eyeball.
+==Locations==
+'''1st Floor'''
+[[Design Space]]
+*Beside the door leading to the metalworking area/back lane (to the left when facing the door)
+[[Metalworking Room]]
+* On the wall beside the main entrance door by the air tank (to the left when facing the door)
+* On the wall to the right of the metal lathe
+'''3rd Floor'''
+[[General Assembly Area]]:
+*On the wall between the IoT Innovation Lab and the 3D printing room
+*On the wall outside the tool room (to the right of the door)
+*Inside Tiny Maker Mind workshop, on the wall opposite the door (member-owned space, do not enter except in case of emergency)
+*To the right of the back elevator/directly across from the paint booth
+* On the wall directly beside the main entrance (to the left when facing the door)
+*
+[[CNC Woodworking Room]]
+* On the wall directly beside the door (to the right when fcing the door)
+[[Woodworking Room]]
+*On the wall directly beside the door (to the right when facing the door)
+[[Epoxy Room]]
+*On the wall directly beside the door (to the right when facing the door
+[[Laser Room]]
+*On the wall directly beside the door (to the right when facing the door)
+[[3D Printing Room]]
+*Inside the room on the wall directly beside the door (to the right when facing the door).
+[[IoT Innovation Lab]]
+*Inside the room on the wall beside the door (to the left when facing the door).