You will be working in the Metal Grinding Room . In order to keep safe from hazards created by you or other workers using any of the tools in this room, the following precautions apply in addition to any other precautions:
We get this by the pallet and the bags are usually either stored on their pallet or on a shelf next to the sandblaster. The media can also be used in the Sandblasting Cabinet (large)/Sandblasting Cabinet (small). It's possible it could also be used in the tumblers.
Mr. Deburr Vibratory Tumbler TrainingIntroduction:
Welcome to the North Forge Fab Lab Mr. Deburr Vibratory Tumbler information page.
for all
is this standard operating procedure or safe work procedure? Not SWP
Cargo
Categories
In this document you will find all the necessary information to safely and efficiently run the Mr. Deburr Vibratory Tumbler.
Safety
PPE
Required PPE for the Vibratory Tumbler include:
SAFETY GLASSES
PROTECTIVE FOOTWEAR
HEARING PROTECTION
for all
According to the manual "Noise levels produced by various Mr Deburr vibratory systems, as measured at the C&M Topline factor, range from 81 to 93 decibels. Do we assume that our machine is at the high end of that range? Considering the small space it is in I would suggest so. If so, the hearing protection that should be used should be an NRR of at least 24. Does the fablab provide this at the tool or should the user provide their own? Ttenbergen (talk) 00:15, 2024 September 27 (CDT)
All other members performing other work in the room would have to wear the same hearing protection while this machine runs.
Cargo
Categories
Nitrile Gloves when mixing solutions
for all
Does the fablab provide these? Also, are protective gloves needed when removing the parts from the tumbler, and are nitrile gloves tough enough for that task?
Cargo
Categories
Splash goggles when mixing or dispensing lubricants
for all
Does the fablab provide these?
Cargo
Categories
Hazards
Splashing lubricant
Handling sharp metal parts
Vibrating machine
Wet floor
Pinching injuries when removing parts from operating machine
Equipment damage due to overloading machine (max capacity 100 lbs)
Eye and skin irritation when using cleaners, rust inhibitors, and other solutions
L-100 is corrosive, others will irritate skin and eyes
for all
what is L-100; we need a sds link on the main page for the tool
Cargo
Categories
If splashed on skin, remove contaminated clothing and rinse affected area
If splashed in eyes, use eye wash to flush the affected eye
for all
manual mentions risk of fire or explosion when using unapproved lubricants, this needs to be reflected here
Cargo
Categories
Machine Overview
The Mr. Deburr 300DB is a deburring and polishing machine. It is designed to deburr parts, and polish a variety of materials using different sets of media. This machine is particularly good at removing rust and getting a high polish and consistent finish on completed metal parts.
Tumbling Media
Currently we have 3 sets of Shop supplied media:
for all
I would like to combine the abrasive media info here because at least some of it can be used in both tumblers and the two sandblasters. Any objections if I move this section to Template:Abrasive media in the metalworking room that has already been applied to the main page of all these tools?
Cargo
Categories
Grey Ceramic
The Grey Ceramic media is designed for steel and stainless steel. It cuts hard and fast, and leaves a matte finish.
Green Resin
The Green Resin cones are designed for softer metals like aluminum and brass.
Corn Cob Polishing Media
Corn cob polishing media can get a highly polished finish on parts, after they go though the primary polish. For example, if you want to mirror polish an aluminum part, first run the part in the Green Resin media to get a consistent finish, then finish the polish in the corn cob media.
Note - we do have corn cob media for both Aluminum and Steel, take care not to cross contaminate the polishing media.
Members are welcome to bring their own media if they have a particular project. Please consult with the trainer to ensure we have space for storage, and to determine which lubricant is ideal for the task/media.
* NEVER tumble steel in the Green Resin Media, and NEVER tumble aluminum in the Grey ceramic media due to the risk of contamination. This creates a very bad finish and the media is extremely time consuming to clean.
Lubrication
Most media is used with a lubricant. North Forge supplies the lubricants for each media. The lubricant is located above the tumbler in dispenser bottles and is labeled for each material. To avoid splash damage, wear safety goggles when dispensing lubricants. A minimal amount of lubricant is ideal, as too much will foam up and cause a mess, and not allow the media to cut properly. One pump of lubricant is sufficient for optimal operation.
Corn Cob media should be run dry.
Operating the Machine
1. Ensure Tumbler is empty and clean
The Tumbler must be cleaned out after every use, so make sure that the tumbling media has been removed.
If there is media still in the tumbler, ensure you put it into the correctly labeled containers.
Wash and scrub the interior of the tank, using water from the hose by the double doors, or the waterjet. A light scrub to remove any possible contaminant is needed to prevent cross contamination between media.
for all
is a brush available for this purpose? Should the splash goggles be worn for this?
Cargo
Categories
2. Prepare Lubricant/Pump
Ensure lubricant bucket is cleaned and scrubbed for use to remove any contamination between media.
Fill bucket with water (from waterjet hose or by the double doors) and one pump of the appropriate lubricant.
Put the bucket under the outflow hose beneath the tumbler, and put the pump into the bucket. Open the outflow valve at the top of the hose, and plug in the pump, ensuring good flow from each indicated hole in the water pipe at the top of the tumbler.
for all
the manual specifies pump precautions and the risk of pump burnout that are not reflected here as a hazard
Cargo
Categories
3. Load Media
Load the correct media into the tumbler. Use all of the media supplied for the correct material. For example, if using the aluminum media, load the tumbler with all of the media.
for all
what is the weight of these buckets? Do we need safe practices for members to handle these safely?
manual mentions plugging outlet drain for dry media like corncob; how do we do that?
Cargo
Categories
4. Prepare Parts for Tumbling
Consider the loads you are putting into the machine. It can handle around 100lbs of parts, however a large amount of parts will reduce the efficiency and surface finish of the parts. Generally, smaller loads with less parts will tumble faster with a better surface finish, however larger loads will not harm the machine.
Flat parts can stick together face-to-face when tumbling due to the lubricant surface tension. It is highly recommended to put 1-2 zip ties on a part in order to prevent the parts from sticking to each other, which also helps with the motion of the tumbling in attaining a faster cutting and more consistent finish. You can run a zip tie through an existing hole in the part. If no holes are on the part you can run without a zip tie attached, however your surface finish may not be as uniform if there are many parts in the tumbler at once.
5. Run Machine
Run the machine, and slowly add parts to the machine.
for all
Run machine how?
Cargo
Categories
Tumbling results can be achieved from as low as 30 minutes, to multiple hours, depending on material, starting surface finish, and machine load.
6. Clean Up/Machine Shutdown
Once you have achieved your ideal surface finish, put gloves on, and remove parts while the machine is running, ensuring that you are aware of what parts are in the machine to avoid injury. The bucket does not have any moving parts or punch points. Once all the parts have been removed turn off the pump, and tumbler.
Let water drain for several minutes. Use that time to rinse and clean your parts.
for all
Where and how do we appropriately do this? There is no utility sink.
Cargo
Categories
Move the media bucket to the media drain. Open the drain and run the machine to shake the media into the buckets.
Put buckets away
for all
Again, we may need to consider safe lifting and moving
Cargo
Categories
Clean the inside to remove contamination.
for all
How?
Cargo
Categories
Take water bucket and pour outside. Rinse and clean bucket.
for all
the bucket will have water, lubricant, abrasive and metal residue. Is it appropriate to dispose of this by pouring this in the lane?
pouring water into the lane in the winter will cause ice, probably not a hazard we want to create
Cargo
Categories
Do any final cleaning and ensure everything is cleaned up.
Troubleshooting:
Issue
Possible Cause
Possible Solution
Water not flowing into tank
Pump Motor Plugged
Remove pump inlet filter, and unscrew the plastic housing (3 screws).
Remove the housing and clean any residue that may be causing the pump not to spin.
for all
we don't generally allow member maintenance; does the fablab approve this exception
Cargo
Categories
Reinstall housing and test
Outflow pipe clogged
The water outflows out of several small holes in the pipe. These holes are indicated with black lines. Use a screwdriver or pointed tool to clean the holes out.
Machine not turning on
Breaker is tripped
Reset the breaker at the pane, in the rented spaces near the machining area
for all
is this a common problem? If so we need to address that. And we need more detailed instructions on which braker.
Cargo
Categories
Motor is overheated
Allow to cool for 30 minutes and try again
for all
is this a common problem? If so we need to address that.